uboot-phytec

# SPDX-License-Identifier: GPL-2.0+

​

obj-$(CONFIG_$(SPL_TPL_)CLK) += clk/

obj-$(CONFIG_$(SPL_TPL_)DM) += core/

obj-$(CONFIG_$(SPL_TPL_)DRIVERS_MISC_SUPPORT) += misc/ sysreset/ firmware/

obj-$(CONFIG_$(SPL_TPL_)I2C_SUPPORT) += i2c/

obj-$(CONFIG_$(SPL_TPL_)LED) += led/

obj-$(CONFIG_$(SPL_TPL_)MMC_SUPPORT) += mmc/

obj-$(CONFIG_$(SPL_TPL_)NAND_SUPPORT) += mtd/nand/

obj-$(CONFIG_$(SPL_TPL_)PHY) += phy/

obj-$(CONFIG_$(SPL_TPL_)PINCTRL) += pinctrl/

obj-$(CONFIG_$(SPL_TPL_)RAM) += ram/

obj-$(CONFIG_$(SPL_TPL_)SERIAL_SUPPORT) += serial/

obj-$(CONFIG_$(SPL_TPL_)SPI_FLASH_SUPPORT) += mtd/spi/

obj-$(CONFIG_$(SPL_TPL_)SPI_SUPPORT) += spi/

obj-$(CONFIG_$(SPL_TPL_)TIMER) += timer/

​

ifndef CONFIG_TPL_BUILD

ifdef CONFIG_SPL_BUILD

​

obj-$(CONFIG_SPL_BOOTCOUNT_LIMIT) += bootcount/

obj-$(CONFIG_SPL_CPU_SUPPORT) += cpu/

obj-$(CONFIG_SPL_CRYPTO_SUPPORT) += crypto/

obj-$(CONFIG_SPL_GPIO_SUPPORT) += gpio/

obj-$(CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT) += ddr/fsl/

obj-$(CONFIG_ARMADA_38X) += ddr/marvell/a38x/

obj-$(CONFIG_ARMADA_XP) += ddr/marvell/axp/

obj-$(CONFIG_ALTERA_SDRAM) += ddr/altera/

obj-$(CONFIG_SPL_POWER_SUPPORT) += power/ power/pmic/

obj-$(CONFIG_SPL_POWER_SUPPORT) += power/regulator/

obj-$(CONFIG_SPL_RESET_SUPPORT) += reset/

obj-$(CONFIG_SPL_MTD_SUPPORT) += mtd/

obj-$(CONFIG_SPL_ONENAND_SUPPORT) += mtd/onenand/

obj-$(CONFIG_SPL_UBI) += mtd/ubispl/

obj-$(CONFIG_SPL_DMA_SUPPORT) += dma/

obj-$(CONFIG_SPL_ETH_SUPPORT) += net/

obj-$(CONFIG_SPL_ETH_SUPPORT) += net/phy/

obj-$(CONFIG_SPL_USB_ETHER) += net/phy/

obj-$(CONFIG_SPL_PCI_SUPPORT) += pci/

obj-$(CONFIG_SPL_PCH_SUPPORT) += pch/

obj-$(CONFIG_SPL_RTC_SUPPORT) += rtc/

obj-$(CONFIG_SPL_MUSB_NEW_SUPPORT) += usb/musb-new/

obj-$(CONFIG_SPL_USB_GADGET_SUPPORT) += usb/gadget/

obj-$(CONFIG_SPL_USB_GADGET_SUPPORT) += usb/gadget/udc/

obj-$(CONFIG_SPL_DFU_SUPPORT) += dfu/

obj-$(CONFIG_SPL_WATCHDOG_SUPPORT) += watchdog/

obj-$(CONFIG_SPL_USB_HOST_SUPPORT) += usb/host/

obj-$(CONFIG_OMAP_USB_PHY) += usb/phy/

obj-$(CONFIG_SPL_SATA_SUPPORT) += ata/ scsi/

obj-$(CONFIG_SPL_USB_HOST_SUPPORT) += block/

obj-$(CONFIG_SPL_MMC_SUPPORT) += block/

obj-$(CONFIG_SPL_FPGA_SUPPORT) += fpga/

obj-$(CONFIG_SPL_THERMAL) += thermal/

​

endif

endif

​

ifdef CONFIG_TPL_BUILD

​

obj-$(CONFIG_TPL_MPC8XXX_INIT_DDR_SUPPORT) += ddr/fsl/

​

endif

​