Commits
Peter Hurley committed bd972688eb2
firewire: ohci: Fix 'failed to read phy reg' on FW643 rev8 With the LSI FW643 rev 8 [1], the first commanded bus reset at the conclusion of ohci_enable() has been observed to fail with the following messages: [ 4.884015] firewire_ohci 0000:01:00.0: failed to read phy reg .... [ 5.684012] firewire_ohci 0000:01:00.0: failed to read phy reg With drivers/firewire/ohci.c instrumented, the error condition [2] indicates the PHY arbitration state machine has timed out prior to enabling PHY LCtrl. Furthermore, instrumenting ohci_enable() shows that LPS has been enabled within 1 ms. Test LPS latching every 1 ms rather than every 50ms. [1] lspci -v 01:00.0 FireWire (IEEE 1394): LSI Corporation FW643 [TrueFire] PCIe 1394b Controller (rev 08) (prog-if 10 [OHCI]) Subsystem: LSI Corporation FW643 [TrueFire] PCIe 1394b Controller Flags: bus master, fast devsel, latency 0, IRQ 92 Memory at fbeff000 (64-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 3 Capabilities: [4c] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [60] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel Capabilities: [170] Device Serial Number 08-14-43-82-00-00-41-fc Kernel driver in use: firewire_ohci Kernel modules: firewire-ohci [2] instrumented WARNING in read_phy_reg() [ 4.576010] ------------[ cut here ]------------ [ 4.576035] WARNING: at ./drivers/firewire/ohci.c:570 read_phy_reg+0x93/0xe0 [firewire_ohci]() [ 4.576050] Hardware name: Precision WorkStation T5400 [ 4.576058] failed to read phy reg:1 (phy(5) @ config enhance:19) [ 4.576068] Modules linked in: hid_logitech_dj hid_generic(+) usbhid <...snip...> [ 4.576140] Pid: 61, comm: kworker/2:1 Not tainted 3.8.0-2+fwtest-xeon #2+fwtest [ 4.576149] Call Trace: [ 4.576160] [<ffffffff8105468f>] warn_slowpath_common+0x7f/0xc0 [ 4.576168] [<ffffffff81054786>] warn_slowpath_fmt+0x46/0x50 [ 4.576178] [<ffffffffa00caca3>] read_phy_reg+0x93/0xe0 [firewire_ohci] [ 4.576188] [<ffffffffa00cae19>] ohci_read_phy_reg+0x39/0x60 [firewire_ohci] [ 4.576203] [<ffffffffa00731ff>] fw_send_phy_config+0xbf/0xe0 [firewire_core] [ 4.576214] [<ffffffffa006b2d6>] br_work+0x46/0xb0 [firewire_core] [ 4.576225] [<ffffffff81071e0c>] process_one_work+0x13c/0x500 [ 4.576238] [<ffffffffa006b290>] ? fw_card_initialize+0x180/0x180 [firewire_core] [ 4.576248] [<ffffffff810737ed>] worker_thread+0x16d/0x470 [ 4.576257] [<ffffffff81073680>] ? busy_worker_rebind_fn+0x100/0x100 [ 4.576266] [<ffffffff8107d160>] kthread+0xc0/0xd0 [ 4.576275] [<ffffffff816a0000>] ? pcpu_dump_alloc_info+0x1cb/0x2c4 [ 4.576284] [<ffffffff8107d0a0>] ? kthread_create_on_node+0x130/0x130 [ 4.576297] [<ffffffff816b2f6c>] ret_from_fork+0x7c/0xb0 [ 4.576305] [<ffffffff8107d0a0>] ? kthread_create_on_node+0x130/0x130 [ 4.576313] ---[ end trace cbc940994b300302 ]--- [Stefan R: Peter also reports a change of behavior with LSI FW323. Before the patch, there would often occur a lock transaction failure during firewire-core startup: [ 6.056022] firewire_core 0000:07:06.0: BM lock failed (timeout), making local node (ffc0) root This failure no longer happens after the patch, without an obvious reason for the failure or the fix.] [Stefan R: Added quirk flag, quirk table entry, and comment.] Reported-by: Tim Jordan <tim@insipid.org.uk> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>