Commits
Tony Lindgren committed 3ca5b7b4afe
USB: serial: option: Add Motorola modem UARTs commit 6caf0be40a707689e8ff8824fdb96ef77685b1ba upstream. On Motorola Mapphone devices such as Droid 4 there are five USB ports that do not use the same layout as Gobi 1K/2K/etc devices listed in qcserial.c. So we should use qcaux.c or option.c as noted by Dan Williams <dan.j.williams@intel.com>. As the Motorola USB serial ports have an interrupt endpoint as shown with lsusb -v, we should use option.c instead of qcaux.c as pointed out by Johan Hovold <johan@kernel.org>. The ff/ff/ff interfaces seem to always be UARTs on Motorola devices. For the other interfaces, class 0x0a (CDC Data) should not in general be added as they are typically part of a multi-interface function as noted earlier by Bjørn Mork <bjorn@mork.no>. However, looking at the Motorola mapphone kernel code, the mdm6600 0x0a class is only used for flashing the modem firmware, and there are no other interfaces. So I've added that too with more details below as it works just fine. The ttyUSB ports on Droid 4 are: ttyUSB0 DIAG, CQDM-capable ttyUSB1 MUX or NMEA, no response ttyUSB2 MUX or NMEA, no response ttyUSB3 TCMD ttyUSB4 AT-capable The ttyUSB0 is detected as QCDM capable by ModemManager. I think it's only used for debugging with ModemManager --debug for sending custom AT commands though. ModemManager already can manage data connection using the USB QMI ports that are already handled by the qmi_wwan.c driver. To enable the MUX or NMEA ports, it seems that something needs to be done additionally to enable them, maybe via the DIAG or TCMD port. It might be just a NVRAM setting somewhere, but I have no idea what NVRAM settings may need changing for that. The TCMD port seems to be a Motorola custom protocol for testing the modem and to configure it's NVRAM and seems to work just fine based on a quick test with a minimal tcmdrw tool I wrote. The voice modem AT-capable port seems to provide only partial support, and no PM support compared to the TS 27.010 based UART wired directly to the modem. The UARTs added with this change are the same product IDs as the Motorola Mapphone Android Linux kernel mdm6600_id_table. I don't have any mdm9600 based devices, so I have only tested these on mdm6600 based droid 4. Then for the class 0x0a (CDC Data) mode, the Motorola Mapphone Android Linux kernel driver moto_flashqsc.c just seems to change the port->bulk_out_size to 8K from the default. And is only used for flashing the modem firmware it seems. I've verified that flashing the modem with signed firmware works just fine with the option driver after manually toggling the GPIO pins, so I've added droid 4 modem flashing mode to the option driver. I've not added the other devices listed in moto_flashqsc.c in case they really need different port->bulk_out_size. Those can be added as they get tested to work for flashing the modem. After this patch the output of /sys/kernel/debug/usb/devices has the following for normal 22b8:2a70 mode including the related qmi_wwan interfaces: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=22b8 ProdID=2a70 Rev= 0.00 S: Manufacturer=Motorola, Incorporated S: Product=Flash MZ600 C:* #Ifs= 9 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=83(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=84(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=86(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=88(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=8a(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=07(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 7 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan E: Ad=8b(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=8c(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=08(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan E: Ad=8d(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=8e(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=09(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms In 22b8:900e "qc_dload" mode the device shows up as: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=22b8 ProdID=900e Rev= 0.00 S: Manufacturer=Motorola, Incorporated S: Product=Flash MZ600 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms And in 22b8:4281 "ram_downloader" mode the device shows up as: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=22b8 ProdID=4281 Rev= 0.00 S: Manufacturer=Motorola, Incorporated S: Product=Flash MZ600 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=fc Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms Cc: Bjørn Mork <bjorn@mork.no> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Lars Melin <larsm17@gmail.com> Cc: Marcel Partap <mpartap@gmx.net> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Michael Scott <hashcode0f@gmail.com> Cc: NeKit <nekit1000@gmail.com> Cc: Pavel Machek <pavel@ucw.cz> Cc: Sebastian Reichel <sre@kernel.org> Tested-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Tony Lindgren <tony@atomide.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>